802.eleventy what? A deep dive into why Wi-Fi kind of sucks

Share on facebook
Share on google
Share on twitter
Share on linkedin
802.eleventy what? A deep dive into why Wi-Fi kind of sucks

When wireless networking based around the 802.11b standard first hit consumer markets in the late nineties, it looked pretty good on paper. Promising “11 Mbps” compared to original wired Ethernet’s 10 Mbps, a reasonable person might have thought 802.11b was actually faster than 10Mbps wired Ethernet connections. It was a while before I was exposed to wireless networking—smartphones weren’t a thing yet, and laptops were still hideously expensive, underpowered, and overweight. I was already rocking Fast Ethernet (100 Mbps) wired networks in all my clients’ offices and my own house, so the idea of cutting my speed by 90 percent really didn’t appeal.

In the early 2000s, things started to change. Laptops got smaller, lighter, and cheaper—and they had Wi-Fi built in right from the factory. Small businesses started eyeballing the “11Mbps” that 802.11b promised and deciding that 10Mbps had been enough for them in their last building, so why not just go wireless in the new one? My first real exposure to Wi-Fi was in dealing with the aftermath of that decision, and it didn’t make for a good first impression. Turns out that “11Mbps” was the maximum physical layer bit rate, not a speed at which you could ever expect your actual data to flow from one machine to another. In practice, it wasn’t a whole lot better than dial-up Internet—in speed or reliability. In real life, if you had your devices close enough to each other and to the access point, about the best you could reasonably expect was 1 Mbps—about 125 KB/sec. It only got worse from there—if you had ten PCs all trying to access a server, you could cut that 125 KB/sec down to 12.5 KB/sec for each one of them.

D-Link's DI-514 802.11b router. It was a perfectly cromulent router for its time... but those were dark days, friend, dark days indeed.

Just as everybody got used to the idea that 802.11b sucked, 802.11g came along. Promising 54 screaming Mbps, 802.11g was still only half the speed of Fast Ethernet, but five times faster than original Ethernet! Right? Well, no. Just like 802.11b, the advertised speed was really the maximum physical layer data rate, not anything you could ever expect to see on a progress bar. And also like 802.11b, your best case scenario tended to be about a tenth of that—5 Mbps or so—and you’d be splitting that 5 Mbps or so among all the computers on the network, not getting it for each one of them like you would with a switched network.

802.11n was introduced to the consumer public around 2010, promising six hundred Mbps. Wow! Okay, so it’s not as fast as the gigabit wired Ethernet that just started getting affordable around the same time, but six times faster than wired Fast Ethernet, right? Once again, a reasonable real-life expectation was around a tenth of that. Maybe. On a good day. To a single device.

The marketers had gotten the bit between their teeth on day one and never let go.

When 802.11ac came to market in late 2013, the boxes in stores hysterically proclaimed faster and faster speeds, many of them several times higher than the fastest consumer wired networking available. As the years went by, it was 1.3 Gbps! 2.7 Gbps! 5.3 Gbps! But by then, I’d long since stopped paying attention. The marketers had gotten the bit between their teeth on day one and never let go. Wi-Fi is nowhere near as fast as wired; the marketing is all lies, lesson learned.

Having given up being excited about Wi-Fi a long time ago, I found it deeply weird when Wi-Fi mesh exploded on the market in 2016, and I wound up reviewing it in-depth.

Unpacking the marketing copy

Let’s say a wireless router offers you an “AC5300” router with “breakthrough tri-band Wi-Fi technology with amazing combined wireless speeds of up to 5,332 Mbps. Thanks to 4×4 data streams, that can be combined through beamforming and MU-MIMO technology to increase reliability and range.” (Actual ad copy from a modern router. It’s not just D-Link, though—Netgear, Linksys, ASUS, and TP-Link all do the same thing.) By now, we hopefully know that absolutely does not mean we’re going to connect a laptop and download things at 600+ MB/sec. But what does it mean?

Things get murky when we try to unpack that “AC5300” speed rating. The way these things are generated is by taking the maximum PHY rate of each radio in the router, multiplied by the maximum number of MIMO streams that radio supports, and adding them all together. The DIR-895L/R is a tri-band device and can transmit and receive on three different Wi-Fi channels at once: two 5 GHz channels and one 2.4 GHz channel. Assuming you don’t have any congestion from your neighbors’ networks, that means you can connect three devices—say, a laptop, a smartphone, and a tablet—all at once, to different radios and on different channels. So far, so good!

We have two 5 GHz radios with 80MHz wide channels and a 2.4 GHz radio with a 40 MHz wide channel, each of which supports up to four MIMO streams. Unfortunately, this doesn’t add up right—433 Mbps per 80 MHz wide 5GHz channel multiplied by four spatial streams comes out to 1,732 Mbps, and D-Link is claiming 2,166 Mbps per 5GHz radio. Where’s that extra 108.5 Mbps per stream coming from? You won’t find a straightforward answer to that question, but depending on your level of cynicism, it’s either “proprietary extensions to 802.11 that your device may or may not support enabling compression that your data may or may not be suitable for,” or “marketing lol.” This is a pretty standard practice now, and it’s the reason why some 3×3 dual-band routers are suddenly jumping from “AC1700” to “AC1900.”

It gets even worse when you examine the 2.4GHz portion of that “AC5300” rating. D-Link is claiming 1,000 Mbps for the 2.4GHz radio. The PHY rate for 40 MHz wide 802.11n 2.4GHz channels is 150 Mbps, though, and 150 Mbps multiplied by four MIMO streams is 600 Mbps. Where’s that missing 400 Mbps coming from? Honestly, it’s anyone’s guess—but it looks like they’re giving themselves an extra 50 Mbps per stream by assuming 256-QAM modulation on 2.4GHz spectrum, even though that’s a non-standard, non-IEEE-approved setup that very few devices will support. That gets you to 800 Mbps. You’re still 200 Mbps short of the 1,000 Mbps claimed, but that’s the same 20 percent that D-Link granted themselves for “compression” on the 5GHz spectrum—so Bob’s your uncle. Probably.

This is what happens when you don't keep a tight rein on the marketing department. All it needs is a <a href="http://www.urbandictionary.com/define.php?term=type%20r%20sticker">Type R sticker</a>.

If what you’re getting out of this so far is “the AC speed rating is always a lie,” you’re not wrong. So let’s get back to what we can actually, hopefully, kinda, expect out of all this.

First of all, let’s talk about that “4×4 MIMO.” It’s great that the router has it, but your client devices—laptops, tablets, and smartphones—don’t. As of February 2017, almost all client devices are either single-stream, or 2×2. Those extra streams aren’t doing you any good if your client devices can’t use them. You might think that’s okay; you can use two MIMO streams for your laptop and two for your tablet. Sorry, but still no—that’s MU-MIMO, which your router may or may not support but your client devices almost certainly don’t. (A very few flagship smartphones like the Galaxy S7 support MU-MIMO, but the only MU-MIMO laptop cards I’ve been able to obtain so far have been off-market bespoke interfaces provided directly by hardware vendors.) It’s also pretty theoretical; the small amount of MU-MIMO testing I’ve managed does show some promise—but it looks better in terms of fairly distributing bandwidth among the MU-MIMO clients than it does for raw performance increases. When I tested enabling MU-MIMO on a router with two MU-MIMO clients connected, it only bumped up their total throughput by about 20 percent. What your client devices all, or almost all, support is SU-MIMO, which still only allows a single device to communicate with the access point at any given time. So if your fastest client device has a 2×2 radio, all you’re ever getting out of that access point is 2×2 speeds, period.

So far, we’ve chopped that “AC5300 up to 5.3 Gbps” router down to one radio at a time, which they’re claiming 2.166 Gbps for. Then we laughed off the “extra speed for compression” that won’t help our JPEGs, MP3s, gzip-compressed HTTP transmissions, or basically anything else we’re likely to care about, which brought us down to 1.732 Gbps. Then we realized we can only connect on two of those four MIMO streams in the ad copy, which brought us down to 866 Mbps.

Are we done yet? Sadly, no. You are never going to see a device actually moving data at PHY rate outside of a carefully designed stream of UDP traffic in an RF isolated and anechoic clean room.

Radio frequency anechoic chamber, Antennas Research Group, Democritus University of Thrace, Greece. The interior surfaces are covered with pyramidal Radiation Absorbent Material (RAM) which are made of rubberized foam impregnated with mixtures of carbon and iron.

Under ideal real-world conditions (10 feet or so distance, no intervening walls, no interference or competition), a single high-quality client device will generally get somewhere between one-third to two-thirds of the PHY rate for the channel it’s connected to, multiplied by the number of MIMO streams it can transmit and receive on. The Qualcomm Atheros AR9462 802.11n 2×2 adapter in my Acer C720 Chromebook (and in a small army of cheap laptops I use for testing) maxes out at somewhere around 205 Mbps, roughly two-thirds of the PHY rate of two 5GHz, 64-QAM, 40 MHz wide MIMO streams. The TP-Link Archer T4U and Linksys WUSB-6300 802.11ac USB3 adapters I use for testing—also 2×2 devices—can almost hit 350 Mbps, which is about 40 percent of PHY. Macbook Pros with the Broadcom BCM94360CS, paired with the right router, can hit real-world ideal condition speeds of 600-ish Mbps… but they’re 3×3 adapters, putting them right back in that same “one-third to two-thirds” bracket.

Now let’s realize that most of the time, we’re probably not going to be sitting 10 feet away from the router with a completely clear line of sight—half the reason we’re wireless in the first place is so that we can wander around the whole house. You’re thirty feet away with two or more walls between you and the router before you realize it, and now you’re looking at more like 80 Mbps… and that’s assuming you’ve got a great wireless client device, a really good access point, and you don’t have any other people or devices competing with you for that radio’s attention.

These devices both use the Realtek RTL8812au 2x2 802.11ac chipset, but with very different results.

If you aren’t disgusted enough with the whole thing yet… a lot of these devices exhibit a strong directional bias, too. The Linksys WUSB-6300 gets about the same speeds up or down, but the Qualcomm AR9462 and the Archer T4U both strongly prefer download to upload, with upload speeds frequently half as good as download, or even worse… and different client device designs, even with the same chipset under the hood, can perform very differently (the WUSB-6300 and the T4U are both Realtek RTL8812au devices).

Testing Wi-Fi is a mess.

See Also:
Share on facebook
Share on google
Share on twitter
Share on linkedin

Sign up To our Newsletter:

Keep connected to the latest Technology news and Products